Saturday, September 2, 2017

Galley Stoves


Some pictures of my galley stoves. There is a Camp Chef two burner stove with a small oven, which can run on disposable propane cylinders or I have a converter hose to go to a 20 lb tank under one of the cockpit seats.
I put a space under the Camp Chef for a drawer, which will bring the height up to be flush with the counter top.

You can see the side of my protective bar, made from a pulpit from an old sailboat, and bent to shape. I was paranoid about stumbling into a hot stove when a rogue wave hit.  
 Here is the Hobbit Stove showing the door open and the protective cage
And here it is as seen from the dinette, i angled the stove so I can watch the flame while relaxing in the saloon.

Tuesday, August 1, 2017

The door in the side of my boat



The Door in the side of my Boat
Aug 1st 2017


I have been working rather erratically on the boat since this spring. I had great plans that the progress would be much further along by now, but thing get in the way, and I am the only one working on this project, and it is my recreation, so I try not to get stressed about it. Anyways, I mentioned to Dave Zeiger, the designer of the Triloboats, that the installation of the door (in nautical terms I think it would be called a hatch)  had taken longer to design, partially due to a lack of suitable examples on the web to copy. So I decided to post some pictures, despite the unfinished state of things.
The reasons for a door is ease of access since the gunnels (the sides) are 5'4" off the bottom, and this boat is designed to be used either from a trailer like a very funky R.V., or dried out on a beach, and even when floating in the water.

I originally was going to have a U shaped hole in the side, but was worried that it would cost too much strength, so changed to a hatch design. There is a vertical 2x6 topped by another 2x6 in a tee shape that runs the length of the boat. Glued inboard of the horizontal piece is a 2x4 the length of the cockpit to strengthen the opening and provides a nice place to sit on top of the gunnel. There will be door, opening outward, with the hinges on the forward side. The door will be slightly larger than the opening, with scuppers in the lower edge.

The area immediately inside the door is sealed off, other than the self draining well just aft of it, which will hold the aft anchor. The plan is that any water that does get in here will flow harmlessly out.
Dimensions of the opening are 18 inches wide by 44 inches tall, but might increase to 46 or so, so that I can put some nice curves at the top of the opening.


The distance from the door to the windows in the saloon is 11 feet, so there is room to store a retracted lee board with out blocking the door or window.



 


There is 32 inches to the transom, allowing an as yet unbuilt bench seat with leanbacks  to be installed across the transom. A folding floor hatch will cover the door well when sailing so that I don't fall in it on a bad tack.









The doubler plate (Green 3/4 ply piece) is 24 inches, and the door is cut 6 inches into it, so the bottom of the door well is 18 inches above the bottom of the boat, or 6 inches above the design water line.
Here is a view of the seat and leanback forward of the door, this is typical of the other seats around the cockpit. This one has a small propane locker on the forward edge, to hold the 20lb bottle that will feed the camp stove inside. It will have a gravity vent so that any leaking propane will go overboard and not into the main cabin. The other compartment or lazarette has a false bottom, so I can empty it and climb down beside the engine if required to service it. I have not built the seat hatches yet, but in the final picture you can see some pieces of ply that will become the seat and back sitting in place.

Monday, February 6, 2017

Engine Hatch Frame Feb 2017

 So my plan is to put this marine Oldsmobile 350 with Berkly Jet pump into my Triloboat. I don't need a 250Hp motor, but it was a fraction of the price of a 25Hp outboard and draws less water. Besides, if I ever want to pull a log off of a beach like Relic in the old Beach Combers series, this is just the motor I need.
So here is the hatch frame, the large opening is just larger than the engine itself, and the smaller hatch behind is over the pump, which needs to be accessible to push the weed grate (Black handle) or to open the port into the pump itself to remove debris (rope is infamous to be sucked up by a jet pump in my reading)
There is a space aft of that hatch, which will end up under the bench seat. This is where I will put my little generator, a Yamaha 2400 with an aftermarket propane kit (it will run on gasoline or propane now)
Another view of the same stuff, just a different angle. You can also see the opening for my door/stairs out the starboard aft quarter (38" from the stern to be more exact)